Products

AOJEL Pro AutoFix Automotive Structural Repair Epoxy

Automotive-focused structural epoxy for rigid parts exposed to oil, road grime, and daily vibration. For Non-safety-critical automotive brackets, housings, rigid metal parts, workshop fixtures, road-exposed rigid repair zones. For materials: Prepared rigid metal substrates: steel, aluminum, cast iron, stainless steel, and compatible hard materials. Not for: Brakes, steering, suspension, tires, airbags, fuel lines, direct flame zones, flexible bumpers, moving joints, safety-critical vehicle systems. Cold-weld style rigid repair body, oil/water resistance after full cure, high-confidence workshop repair control. How to use:  Remove oil/road film/rust -> roughen -> mix 1:1 uniformly -> apply and align -> clamp/support -> cure fully before service. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h before heavy vehicle stress service. Heat, Hardness, Water, Oil: Up to 392F (200C) after full cure; Shore D 85-90 typical range; waterproof and oil resistant after full cure. Safety notes: For non-safety-critical repairs only; follow professional automotive safety standards. FQA: Can AutoFix repair any car part? No, not safety-critical systems. Can I apply over oily metal? No, degreasing is mandatory before bonding. Is this a weld replacement? Not for certified structural or safety-critical weld applications.

AOJEL Pro MarineFix Marine and RV Repair Epoxy

Clear marine/RV repair epoxy for wet, outdoor, and vibration-prone rigid environments. For Boat and RV rigid repair points, outdoor components, moisture-exposed hard surfaces, vibration-prone reinforcement zones. For materials: Prepared fiberglass, rigid plastics, metal, glass, ceramic, and other rigid hard materials. Not suitable for: Flexible inflatables, moving joints, active pressurized leaks, direct flame, safety-critical marine/vehicle systems. Core performance: Clear repair body, waterproof after full cure, strong adhesion on prepared rigid surfaces in outdoor/wet-use scenarios. How to use:  Clean and dry -> roughen -> mix 1:1 uniformly -> apply precisely -> support/reinforce vibration zones -> allow full cure before water or load exposure. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h for demanding marine/RV stress use. Heat, Hardness, Water, Oil: Waterproof after full cure; clear/colorless transparent cured finish; oil resistance after full cure on compatible rigid materials. Safety notes: Clear does not guarantee invisible repair; final appearance depends on thickness, substrate, and lighting. FQA: Is MarineFix waterproof? Yes, after full cure. Can I apply on wet/oily surfaces? No, prep is still required. Is the repair invisible? No guaranteed invisibility claim should be made.

AOJEL Pro MatelBond Cold-Weld Metal Repair Epoxy

Cold-weld style metal repair epoxy for cracks, holes, and rebuildable rigid damage. For Metal cracks, chipped castings, worn corners, missing sections, hole rebuilding, drill-and-finish repairs. For materials: Prepared steel, aluminum, cast iron, stainless steel, and compatible rigid hard materials. Not suitable for: Certified weld replacement in safety-critical structures, flexible joints, gas lines, active pressure leaks, direct flame. Core performance: Rigid metal-focused repair body; drillable/sandable/fileable/paintable after full cure; reinforcement-friendly for stressed repairs. How to use:  Clean and roughen -> mix 1:1 until uniform -> apply with adequate thickness -> add backing/mesh if needed -> full cure -> finish. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h before high stress service. Heat, Hardness, Water, Oil: Heat resistance up to 392F (200C) after full cure; Shore D 85-90 typical range; waterproof and oil resistant after full cure. Safety notes:  Cold-weld style means no flame, but not a regulatory weld substitute in certified systems. FQA: Can it fill holes? Yes, with proper thickness and reinforcement when needed. Can I drill/sand later? Yes, after full cure. Is this identical to welding? No, it is an epoxy-based cold-weld style repair method.

AOJEL Pro PipeSeal Structural Pipe Repair Epoxy

External pipe and fitting reinforcement epoxy for dry, prepared, rigid repair surfaces. For External pipe cracks, fitting joints, dry-surface leak reinforcement, rigid pipe-adjacent repairs. For materials: Prepared rigid metal and compatible hard pipe-adjacent substrates. not suitable for: Gas lines, active high-pressure leaks, code-critical plumbing, drinking-water contact unless certified, flexible hoses/moving joints. Rigid reinforcement body, waterproof/oil resistant after full cure, supports layered/patch-based external repair strategy. How to use:  Depressurize and dry -> clean/roughen -> mix 1:1 -> apply with overlap -> add mesh/patch if needed -> full cure before pressure return. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h before high-stress service. Heat, Hardness, Water,Oil: Up to 392F (200C) after full cure; Shore D 85-90 typical range; waterproof and oil resistant after full cure. Safety notes:  Not a stand-alone solution for unsafe plumbing or pressure-critical systems. FQA: Can it stop an active leak immediately? No, pressure must be controlled first. Can I use it on gas lines? No. Is it for code-critical plumbing? No, follow local plumbing code and licensed repair requirements.

AOJEL Pro ThermaBond High-Heat Repair Epoxy

High-heat and fluid-exposure structural epoxy for rigid engine-adjacent repair environments. For Heat-adjacent metal brackets, housings, rigid thermal-stress repairs, workshop fluid-exposure zones. For materials: Prepared rigid metals and compatible hard materials in non-safety-critical heat-exposed applications. Not suitable for: Direct flame, fuel lines, active pressure systems, flexible joints, safety-critical automotive systems, zones above rated conditions. Core performance: Rigid structural repair body with high heat tolerance after full cure; finishable and durable under proper prep and cure conditions. How to use:  Degrease/clean -> roughen -> mix 1:1 uniformly -> apply and align -> support -> full cure before heat/fluid/load exposure. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h before severe heat/fluid service. Heat, Hardness, Water, Oil: Heat resistance up to 392F (200C) after full cure; Shore D 85-90 typical range; waterproof and oil resistant after full cure. Safety notes: Do not position as a replacement for certified repairs in critical thermal/pressure systems. FQA: Can I use it near engine heat? Yes, in non-safety-critical, within-rated, prepared areas. Can it be applied on oily metal? No, clean first. Can I use it on exhaust flame path? No, not for direct flame/exhaust extremes.

AOJEL S300 Core Metal Epoxy

The core structural repair epoxy for rigid metal and hard-material damage that must hold.  For Metal cracks, broken brackets, damaged housings, rigid tool repair, cast defects, frame edges, fittings, non-flexing structural reinforcement. Steel, aluminum, cast iron, stainless steel, ceramic, stone, fiberglass, wood, and other prepared rigid hard materials. Not for: PE/PP/PTFE/silicone, soft plastics, flexible joints, moving joints, active high-pressure leaks, gas lines, direct flame, drinking-water contact unless certified, safety-critical systems (brakes/steering/suspension/airbags/load-rated structures). 2-part structural repair body, load-bearing reinforcement, waterproof and oil resistant after full cure, finishable repair result. How to use:  Clean and degrease -> roughen surface -> mix A/B 1:1 until uniform -> apply beyond crack line (0.5-1 in overlap) -> reinforce stress points if needed -> keep stable during cure. Cure_time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; wait 24-48h before heavy load/heat/fluid service. heat, hardness, water, oil: Heat resistance up to 392F (200C) after full cure; Shore D 85-90 typical range; waterproof and oil resistant after full cure. Safety notes: Not a replacement for certified welding or code-compliant mechanical repair in safety-critical applications.  FAQ: Can I use S300 on aluminum? Yes, on clean and roughened rigid aluminum surfaces. Can I drill after cure? Yes, after full cure. Why did it stay sticky?  Usually incomplete mixing, contaminated surface, or early testing before full cure. Can it stop an active pressurized leak? No. Depressurize and repair safely first.

HerFix JewelryFix L4 Clear Jewelry Repair Epoxy

HerFix JewelryFix L4 is clear jewelry and glass repair epoxy for small visible repairs requiring careful placement. For Jewelry findings, decorative glass, transparent parts, small visible detail repairs where alignment and finish are critical. For materials: Prepared rigid jewelry and hard decorative substrates, glass, and compatible transparent components. Not suitable for: High-value irreplaceable items without testing, flexible settings, soft plastics, uncertain coatings/platings, safety-critical wear parts. Core performance: Clear cured finish with controlled working window for alignment and precise low-volume application. How to use:  Test discreetly if needed -> clean/roughen -> mix 1:1 -> apply very small amount -> align and hold stable -> full cure before use. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; delay wear/load for stronger final result. Heat, Hardness, Water, Oil: Clear/colorless transparent cured finish; water/oil resistance after full cure on compatible rigid surfaces. Safety notes: No adhesive should be marketed as guaranteed invisible on every stone, plating, coating, or luxury material. FAQ Can I use on fine jewelry? Test first and use pro jeweler service for high-value pieces. Will it become invisible? Not guaranteed. Is it for moving clasp joints under constant stress? Not recommended.  

HerFix LeakLock L1 Household Leak Repair Epoxy

Household-focused leak and crack reinforcement epoxy for practical home repair control. For Leak-prone seams, rigid household cracks, fittings, joints, emergency reinforcement before full replacement. For materials: Prepared rigid metal, PVC, ceramic, and compatible hard household substrates. Not suitable for: Active high-pressure leaks, gas lines, code-critical plumbing, flexible hoses/joints, unsafe live systems. Core_performance: Household reinforcement body with waterproof performance after full cure and controlled cartridge application. How to use:  Shut source/depressurize -> dry/clean/roughen -> mix 1:1 -> apply with overlap -> reinforce if needed -> cure fully before service. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h before stress/water pressure service. Heat, Hardness, Water, Oil: Silver-gray/metallic-gray cured finish; waterproof and oil resistant after full cure; rigid reinforcement behavior. Safety notes: Household repair aid, not a legal replacement for licensed plumbing work when required by code. FAQ: Can it permanently replace plumbing repair? No, it is a reinforcement material. Can I use on wet active leaks? Best results require dry, prepared surfaces. Is it safe for gas lines? No.

HerFix MicroBond L3 Precision Clear Repair Epoxy

Precision clear epoxy for small everyday rigid repairs where control and cleaner finish matter. For cases: Small objects, edge chips, daily household items, ceramic/stone/PVC detail repairs, low-volume precision fixes. For materials: Prepared rigid hard surfaces including ceramic, stone, PVC, metal, glass, and compatible plastics. Not suitable for: Large-volume filling, flexible joints, active leaks, safety-critical structures, guaranteed invisible repair claims. Core performance: Clear cured finish, precise placement behavior, compact cartridge efficiency for small repairs and reduced waste. How to use:  Prep and roughen -> mix 1:1 uniformly -> apply small controlled amount -> align/stabilize -> full cure before stress. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; allow longer before heavy stress. Heat, Hardness, Water, Oil: Clear/colorless transparent finish; waterproof and oil resistant after full cure on compatible rigid surfaces. Safety notes: Precision product for focused repairs, not bulk filling or structural safety-critical repairs. FAQ: Is MicroBond for large repairs? No, it is for precision small-scale repair. Is clear equal to invisible? No, visual result depends on thickness and lighting. Can it repair flexible rubber? No.

HerFix PipeSeal L5 Home Pipe and Joint Repair Epoxy

HerFix PipeSeal L5 is for clear home pipe/joint emergency reinforcement epoxy for household rigid leak-prone areas. For Home pipe joints, minor rigid cracks, emergency reinforcement around household fittings and joints. For materials: Prepared rigid PVC, metal, and compatible hard household pipe-adjacent surfaces. Not suitable for: Active high-pressure leaks, gas lines, code-critical plumbing, drinking-water contact unless certified, flexible hoses/joints. Core performance: Clear reinforcement body for controlled household patch-style repair after proper prep and full cure. How to use:  Control pressure -> clean/dry/roughen -> mix 1:1 -> apply with overlap and support -> full cure before re-service. Cure time: Initial set 3-4h; handling cure 8-12h; full cure 24h typical; 24-48h before pressure/heavy service. Heat, hardness, water, oil: Clear/colorless transparent cured finish; waterproof and oil resistant after full cure on rigid prepared surfaces. Safety notes: Emergency home reinforcement tool, not a substitute for required code-compliant plumbing repair. FAQ: Can this fix pressurized leaks immediately? No. Is this for gas lines? No. Is it safe for potable-water contact? Only if explicitly certified for that use.

HerFix TileFix L2 Tile and Stone Repair Epoxy

A 2:1 no-drip tile/stone/ceramic repair epoxy for edge chips, cracks, and visible surface control. For Tile chips, ceramic edge damage, stone cracks, corner rebuild, vertical surface touch-ups with non-sag control. For materials: Prepared tile, stone, ceramic, and compatible rigid hard surfaces. Not suitable for: Flexible movement joints, soft plastics, active leaks, large unsupported voids, guaranteed invisible color-match claims. Core performance: 2:1 controlled non-sag repair behavior with clear-to-translucent finish for surface repair precision. How to use:  Clean/dry/roughen -> mix in 2:1 ratio thoroughly -> place in controlled thin-to-medium layers -> shape/finish after full cure. Cure time: Follow 7026 label/SDS cure guidance; allow full cure before water, abrasion, or impact service. Heat, Hardness, Water, Oil: Clear-to-translucent cured finish; no-drip behavior for vertical/detail repair control. Safety notes: TileFix L2 is the only current 2:1 product in this set. FAQ: Is TileFix 1:1? No, it is 2:1. Will the repair be invisible? No guaranteed invisibility. Can I use on moving grout lines? Not recommended for movement joints.